Your 2006 Hummer H2problems, repair costs and recalls
What we've documented about the 2006 Hummer H2: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2006 Hummer H2
16 documented issues apply to 2006, most serious first.
Blower motor wiring or resistor overheats
- What you'll notice
- A burning electrical smell, the fan working only on some speeds or cutting out, and in some reports melted plastic or smoke near the glove box.
- Why it happens
- The blower motor resistor and its wiring connector carry a lot of current and can overheat. Owners report melted connectors and harnesses on many H2 model years.
- What to do
- Turn the fan off and get it checked if you smell burning plastic. The resistor and its connector or pigtail should be replaced together.
Rusted brake lines burst (pedal sinks to the floor)
- What you'll notice
- The brake pedal suddenly goes soft or sinks to the floor, brake fluid leaks under the truck, or the brake warning light comes on.
- Why it happens
- The steel brake lines that run under the truck rust, especially where roads are salted, and eventually burst. Owners report sudden loss of braking with little warning.
- What to do
- If the pedal goes soft, stop driving and have the truck towed. On older H2s, have the brake lines inspected for heavy rust and replace them before they fail.
Heated washer fluid system fire risk (recall)
- What you'll notice
- Washer fluid heater problems, an electrical burning smell, smoke from under the hood, or other electrical faults.
- Why it happens
- The heated windshield washer system had a circuit board and ground wire that could short and overheat. GM issued recalls, first adding a fused harness and later disabling the module, because it could start a fire.
- What to do
- Make sure the heated washer recalls are done on your VIN. Until then, stop using the heated washer feature and have it checked if you smell burning.
Front ball joint or steering knuckle failure
- What you'll notice
- Clunking from the front end, wandering steering, uneven tire wear, and in the worst cases a front wheel that collapses or comes off the truck.
- Why it happens
- The heavy H2 and its big tires put high loads on the front ball joints and steering knuckles. Owners report ball joints snapping and front wheels separating, sometimes at speed.
- What to do
- Have the ball joints and knuckles checked at every tire rotation, especially on lifted trucks or those with larger tires. Replace worn joints right away.
Airbag light on (airbag module or water damage)
- What you'll notice
- The airbag warning light comes on and stays on, sometimes with a service message or other modules acting up.
- Why it happens
- The airbag control module (SDM) can fail, and some owners trace it to rain water leaking into the cabin near the module.
- What to do
- The airbags may not work while the light is on. Have the codes read, fix any water leak first, then repair or replace the module.
Automatic transmission slipping or stuck in gear
- What you'll notice
- Slipping between 1st and 2nd, flaring engine revs, delayed engagement, or the transmission sticking in one gear.
- Why it happens
- The heavy-duty 4-speed automatic behind the 6.0L works hard moving a 6,400-pound truck, and its clutches wear out. Owners report slipping and stuck-in-gear problems.
- What to do
- Check the transmission fluid level and smell. Have it diagnosed before it gets worse; frequent towing or big tires make wear faster.
Frame and subframe rust
- What you'll notice
- Clicking when turning the steering wheel, heavy rust on the frame and underbody, or rusted-through brackets.
- Why it happens
- Road salt corrodes the H2’s frame and steel underbody parts. A dealer traced one owner’s clicking to a rusted subframe support.
- What to do
- Have the frame inspected, especially on trucks from snowy states. Treat rust early with an undercoating; severe rust needs welding repair.
Low oil pressure or failing lifters
- What you'll notice
- Low oil pressure warning, a ticking or tapping from the engine, or the gauge reading lower than normal.
- Why it happens
- Owners report collapsed or failed valve lifters and low oil pressure on high-mileage 6.0L engines.
- What to do
- Stop driving if the oil pressure light comes on. Check the oil level, then have a shop test oil pressure before more damage occurs.
Broken exhaust manifold bolts (ticking exhaust leak)
- What you'll notice
- A ticking or tapping noise from the engine bay that is loudest on a cold start, sometimes an exhaust smell inside or around the truck, and in some cases a check engine light.
- Why it happens
- The bolts holding the cast-iron exhaust manifolds to the 6.0L cylinder heads snap after years of heating and cooling. Once a bolt breaks, exhaust leaks past the gasket. Owners have reported this on many H2s, sometimes with damage to nearby parts.
- What to do
- Have the manifold area checked for broken bolts. A leak near the cabin can let exhaust fumes in, so do not ignore a strong exhaust smell. Broken bolts usually have to be drilled out, so pick a shop that has done this job before.
Speedometer and gauges stick or stop working
- What you'll notice
- The speedometer, tachometer or other gauges freeze, jump around, drop to zero at speed or stop working entirely. Warning lights may come on together or the cluster backlighting may fail.
- Why it happens
- Components inside the instrument cluster fail with age, especially the small motors that move the needles. Owners report it at many mileages on these years.
- What to do
- Use a phone GPS app to check your speed until it is fixed. A cluster rebuild service is usually much cheaper than a new dealer cluster, which also needs programming.
Air blows from the wrong vents or will not cool
- What you'll notice
- Air only comes out of the defrost vents, the A/C blows warm air, or you cannot change where the air comes out. You may hear a clicking behind the dash.
- Why it happens
- An electric mode or blend door actuator behind the dashboard fails. It is the small motor that moves the flaps that send air to each vent or mix hot and cold.
- What to do
- Have the HVAC system scanned to find which actuator has failed. It is usually a modest repair, and a battery change or disconnect can trigger a relearn.
Loose, wandering steering (worn pitman and idler arms)
- What you'll notice
- Steering feels vague or loose at highway speed, the truck wanders in its lane, or the steering wheel has play.
- Why it happens
- The pitman arm and idler arm that connect the steering box to the front wheels wear out under the H2’s weight. Owners often add a heavy-duty reinforcement kit when replacing them.
- What to do
- Have the steering linkage inspected and the front end aligned after any repair. Worn steering parts can also make braking feel unsettled.
No-start from theft system or ignition switch
- What you'll notice
- The engine cranks but will not start or will not crank at all, sometimes with a security light, then starts after waiting several minutes. The key may stick in the ignition.
- Why it happens
- The Passlock theft-deterrent system and the ignition switch or lock cylinder can fail with wear, so the computer stops fuel or cranking.
- What to do
- Note whether the security light is on when it will not start. A shop can read the theft-system codes; the fix is usually an ignition switch, lock cylinder or Passlock sensor.
Power window falls into door or stops working
- What you'll notice
- A window will not go up or down, makes a grinding noise, or drops down into the door.
- Why it happens
- The window regulator cable or motor in the door fails. Owners report rear windows dropping and getting stuck open.
- What to do
- Tape plastic over the opening to keep rain out until it is fixed. The regulator and motor are often replaced together.
ABS and traction control lights come on
- What you'll notice
- The ABS and traction control lights flicker on and off; in one case gauges, windows and locks lost power at the same time.
- Why it happens
- Faults in the ABS control module or wheel speed sensor wiring set warning lights. GM also recalled some trucks for reversed wheel speed sensor wires.
- What to do
- Have the ABS codes read. Normal braking still works, but ABS and traction control may be off.
Front differential seal and transmission cooler line leaks
- What you'll notice
- Oil spots under the front of the truck or a small leak at the front differential or transmission cooler lines.
- Why it happens
- Seals on the front differential and fittings on the transmission cooler lines can seep, even on low-mile trucks.
- What to do
- Have the leak located and fixed before fluid levels drop, which can damage the differential or transmission.
Repair prices for your 2006 Hummer H2
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Extract broken manifold bolts and replace manifold gasket (one side)
- Remove instrument cluster, send out for rebuild, reinstall
- Replace HVAC mode/blend door actuator
- Replace blower motor resistor and connector pigtail
- Replace rusted brake lines and bleed the system
- Replace front lower ball joints or control arms (both sides)
- Replace pitman arm and idler arm, align front end
- Replace ignition switch or lock cylinder and relearn theft system
- Diagnose airbag system and replace airbag control module
- Rebuild or replace 4-speed automatic transmission
- Replace front differential seal or transmission cooler line
- Replace window motor and regulator assembly
- Diagnose ABS codes; replace wheel speed sensor or ABS module
- Repair rusted subframe support or frame section
- Replace lifters and related valvetrain parts (or engine)
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Recall: install fused harness or disable heated washer moduleNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…