Nissan Frontierproblems, repair costs and recalls
Problems reported across 1998–2026. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
39 documented issues across all years, most serious first.
Distributor shaft seizing (stalls or will not start)
- What you'll notice
- The engine cuts out in traffic, runs rough, or cranks but will not start. It may restart after cooling down, then quit again.
- Why it happens
- First-generation trucks use a distributor, and its shaft bearing can rust and bind. As it drags, ignition timing and spark become erratic until the engine dies.
- What to do
- Do not rely on the truck until it is fixed, since it can stall in traffic. Have the ignition system checked and replace the distributor if the shaft is binding.
Lower steering shaft joint can corrode (recall)
- What you'll notice
- Steering may feel stiff or notchy, especially at full lock during slow turns or parking.
- Why it happens
- Road salt can rust the lower steering shaft joint. A badly corroded joint can crack and cause loss of steering control at low speed. Nissan recalled affected trucks.
- What to do
- Check your VIN for open recalls right away and have the shaft inspected. If the steering binds or feels unusual, do not drive it until it is checked.
Coolant leaking into the automatic transmission
- What you'll notice
- Shuddering, slipping, or harsh shifts, and transmission fluid that looks pink and milky. Coolant may also go low.
- Why it happens
- The transmission cooler built into the radiator can crack inside, letting coolant and transmission fluid mix and ruining the transmission. Nissan extended radiator warranty coverage on many of these trucks after a class action.
- What to do
- Stop driving if it slips badly. Have the radiator and fluid checked right away. If the original radiator is still in place, many owners replace it as prevention.
Front crash zone sensor corrosion (recall)
- What you'll notice
- The air bag warning light comes on.
- Why it happens
- Water and road salt can corrode the front crash zone sensor, which can prevent the front air bags from deploying correctly. Nissan recalled affected trucks.
- What to do
- Check your VIN for open recalls and have the sensor replaced. Treat an air bag light as a real fault until it is checked.
Engine control relay can stall the engine (recall)
- What you'll notice
- The engine shuts off while driving, sometimes without warning, and may restart after a moment.
- Why it happens
- Oxide can build up on the contacts of a relay that powers the engine controls, cutting power to the engine. Nissan recalled affected trucks to replace the relay.
- What to do
- Check your VIN for this recall and get it done before regular driving, because a stall at speed is dangerous.
Fuel tank can deform and fool the gauge (recall)
- What you'll notice
- The gauge shows fuel left, often around a quarter tank, when the tank is actually empty, and the truck runs out of gas.
- Why it happens
- The fuel tank on certain trucks can deform so the gauge cannot read the true level. Nissan recalled affected trucks.
- What to do
- Check your VIN for this recall. Until it is done, refuel early and do not trust a low gauge reading.
Fuel tank can deform and fool the gauge (recall)
- What you'll notice
- The gauge shows fuel left, often around a quarter tank, when the tank is actually empty, and the truck runs out of gas.
- Why it happens
- The fuel tank on certain trucks can deform so the gauge cannot read the true level. Nissan recalled affected trucks.
- What to do
- Check your VIN for this recall. Until it is done, refuel early and do not trust a low gauge reading.
Steering wheel emblem can come loose (recall)
- What you'll notice
- No warning signs before a crash.
- Why it happens
- The emblem on the driver air bag cover can crack and break off when the air bag deploys, and could strike the driver. Nissan recalled affected trucks.
- What to do
- Check your VIN for open recalls and have the free repair done.
Weak lower control link welds (recall)
- What you'll notice
- Usually none before a failure. A separated link would make the truck handle poorly or pull unexpectedly.
- Why it happens
- Some lower control links on trucks built in late 2009 and early 2010 had welds below specification that could separate. Nissan recalled them.
- What to do
- Check your VIN for this recall and have the links inspected or replaced before relying on the truck.
Front wheel hubs may crack on 2WD trucks (recall)
- What you'll notice
- A clunk, wobble, or new noise from a front wheel. In the worst case the wheel can separate.
- Why it happens
- Some two-wheel-drive trucks built in mid-2012 got front hubs that were not hardened enough and could crack. Nissan recalled them.
- What to do
- Check your VIN for this recall. If you notice a wobble or clunk from the front, stop driving and have it inspected.
Backward circuit breaker can short the wiring (recall)
- What you'll notice
- Electrical items may stop working, and a short can cause a burning smell or smoke.
- Why it happens
- A circuit breaker could be installed backward, letting the wiring harness rub against it until it shorts. Nissan recalled affected trucks.
- What to do
- Check your VIN for this recall. If you smell burning wires, stop and have the truck inspected before driving again.
Starter wiring can short on the heat shield (recall)
- What you'll notice
- Possible burning smell, smoke from under the truck, or starting trouble.
- Why it happens
- On some V6 trucks built in early 2016, the starter cable could touch the heat shield and short out, creating a fire risk. Nissan recalled them.
- What to do
- Check your VIN for this recall and get it done promptly. If you smell burning, stop and have it inspected.
Ignition can slip out of Run and stall (recall)
- What you'll notice
- The engine suddenly shuts off while driving, often after the key or key ring is bumped, and power steering and brake assist are lost.
- Why it happens
- On trucks with a turn key, the ignition switch can move from Run to Accessory too easily. Nissan recalled affected trucks.
- What to do
- Check your VIN for this recall. Until it is fixed, remove heavy items from the key ring and keep your knees clear of the key.
Park may not engage and the truck can roll away (recall)
- What you'll notice
- The truck rolls after the shifter is placed in Park, sometimes several feet before it stops.
- Why it happens
- The parking pawl in the 9-speed automatic may not engage fully. Nissan recalled these trucks, first for parts and then for a transmission software update.
- What to do
- Check your VIN for both recalls. Until they are done, always set the parking brake and confirm the truck is held before getting out.
Tire inner bead can tear (recall)
- What you'll notice
- A sudden loss of air in a tire, which can cause a blowout or loss of control.
- Why it happens
- The inner bead area of the tires fitted to some trucks could tear. These tires were recalled.
- What to do
- Check your VIN for this recall and have the tires inspected or replaced. Stop safely if a tire suddenly loses air.
Front lower ball joint can corrode and separate (recall)
- What you'll notice
- A clunk or loose feeling from the right front, or wandering steering. A separated joint can cause loss of steering control.
- Why it happens
- The ball joint on the right front lower link could corrode and pull apart. Nissan recalled affected trucks.
- What to do
- Check your VIN for this recall and get it done before regular driving. Stop driving if you notice new front-end clunks or loose steering.
Door striker welds can break (recall)
- What you'll notice
- A door may not latch firmly, rattle, or feel loose when closed.
- Why it happens
- Some door strikers were poorly welded and could crack or separate, which could let a door open while driving. Nissan recalled affected trucks.
- What to do
- Check your VIN for this recall and have it repaired promptly. If a door will not latch securely, do not carry passengers in that seat until it is fixed.
Shifter can come out of Park with the key removed (recall)
- What you'll notice
- The lever can be moved out of Park without the key in the ignition, and the truck can roll away.
- Why it happens
- A pin that secures the shift mechanism can work loose, so the interlock that should hold the lever in Park no longer does.
- What to do
- Always set the parking brake and have the interlock repaired. The truck can roll while parked.
Front seat belt webbing can be cut by the recliner handle (recall)
- What you'll notice
- Frayed or cut webbing on a front seat belt, or a belt that will not retract smoothly.
- Why it happens
- On bucket seats the belt can slip past the seat back recliner handle, where the edge can cut into the webbing.
- What to do
- Have the belts inspected and replaced. A cut belt can break in a crash.
Fuel pump wiring terminal can crack and corrode (recall)
- What you'll notice
- Long cranking, a stall at low speed or while idling, or the engine will not start at all.
- Why it happens
- The electrical terminal on the in-tank fuel pump can crack and corrode, which cuts power to the pump.
- What to do
- Have it checked before it strands you or stalls you in traffic; the pump assembly is replaced.
Shift cable lock plate can break (recall)
- What you'll notice
- The gear shown on the indicator does not match the gear the truck is actually in, or it will not stay in Park.
- Why it happens
- A plastic lock plate on the shift cable can break, which lets the cable and the lever get out of step.
- What to do
- Have it repaired right away. The truck can move in a gear you did not select or roll out of Park.
Fuel can spill from the filler neck valve (recall)
- What you'll notice
- A strong fuel smell or wet fuel around the filler area, usually after filling the tank or on rough roads.
- Why it happens
- A shutter valve in the tank inlet may not seal properly, so fuel can escape past it.
- What to do
- Keep it away from heat and sparks and have it fixed promptly. Spilled fuel is a fire risk.
Oil cooler bolts can break and leak oil (recall)
- What you'll notice
- Oil on the ground or sprayed under the engine, a low oil light, or a burning oil smell.
- Why it happens
- The bolts holding the oil cooler and filter housing can break, which opens a path for oil to escape under pressure.
- What to do
- Stop driving if the oil light comes on. Losing oil pressure can destroy the engine.
Rear seat belt anchor bolt may not hold (recall)
- What you'll notice
- Nothing is usually noticed day to day; the rear belt anchor may be loose when pulled on.
- Why it happens
- An out-of-spec nut was used at the rear seat belt anchor, so the anchor may not stay attached under crash loads.
- What to do
- Have the anchor hardware inspected and replaced before carrying passengers in the back.
Left rear seat belt bracket bolts can be loose (recall)
- What you'll notice
- The left rear belt mount feels loose or moves when the belt is pulled hard.
- Why it happens
- The bolts holding the bracket were not tightened to specification at the factory.
- What to do
- Have the bolts checked and torqued before using that seating position.
Missing tow hitch leaves the fuel tank exposed (recall)
- What you'll notice
- Nothing is noticed in normal driving; a crew cab long bed truck has no hitch where one should be.
- Why it happens
- The hitch also acts as protection for the fuel tank in a rear impact, and some trucks left the plant without it.
- What to do
- Have the dealer check the build and install the hitch. Without it a rear crash can damage the tank.
Timing chain whine (4.0L)
- What you'll notice
- A high-pitched whine or buzz from the front of the engine that rises with engine speed. Later it can rattle or set timing-related codes.
- Why it happens
- The plastic guides and tensioner shoes for the timing chains wear quickly and can break apart. Nissan issued a service bulletin covering the noise.
- What to do
- Have it diagnosed soon. Replacing the chains, guides and tensioners before a guide breaks avoids much more serious engine damage.
Fuel gauge reads wrong (sending unit)
- What you'll notice
- The gauge sticks, reads full or empty when it is not, the distance-to-empty display goes blank, and the check engine light may come on.
- Why it happens
- The fuel level sending unit inside the tank wears and sends a false reading.
- What to do
- Track mileage between fill-ups so you do not run dry, and have the sending unit tested and replaced.
Rear axle seal leaks
- What you'll notice
- Gear oil on the inside of a rear wheel or tire, a wet brake backing plate, weak rear braking, or grinding from the rear axle.
- Why it happens
- The rear axle shaft seals can leak, sometimes because a clogged axle vent lets pressure build. Leaking oil can soak the rear brakes and starve the axle bearings. Nissan issued a service bulletin on these leaks.
- What to do
- Have the seals replaced and the vent checked. Replace any oil-soaked brake parts, and top up the axle oil so the bearings and gears are not damaged.
Rough or erratic shifting (9-speed automatic)
- What you'll notice
- Harsh or delayed shifts, gear hunting on the highway, clunks at low speed, hesitation when pulling away, or a gear-shaped warning or AT Check light.
- Why it happens
- Owners widely report shift-quality problems with the 9-speed automatic. Dealers often address them with transmission software updates, and some have replaced the shifter.
- What to do
- Have the dealer scan for codes and check for software updates. Get it looked at sooner if a warning light comes on or the truck stalls.
Backup camera may show a blank screen (recall)
- What you'll notice
- The center screen stays blank when the truck is put in reverse.
- Why it happens
- A software problem could stop the rear camera image from displaying. Nissan recalled affected trucks for a software update.
- What to do
- Check your VIN for this recall. Until it is done, check mirrors and look behind you when backing up.
Tail lamp bulb can fall out of its socket (recall)
- What you'll notice
- A brake light or tail light that flickers or stops working, sometimes coming back when the bulb is pushed in.
- Why it happens
- The socket may not hold the bulb firmly, so the contact is lost with vibration.
- What to do
- Have the socket or lamp assembly replaced so drivers behind can see your brake lights.
Water in the rear axle can ruin the wheel bearings (recall)
- What you'll notice
- A growl or hum from the back that changes with speed, or play felt at a rear wheel.
- Why it happens
- Water gets into the rear axle past the seal around the wheel speed sensor and rusts the bearings from the inside.
- What to do
- Have the rear bearings and the seal checked. Worn bearings get noisy first and can fail later.
Supercharged engine can drop into a low power mode (recall)
- What you'll notice
- The engine suddenly will not rev past a low limit and the truck feels very slow, often with a warning light.
- Why it happens
- The control system can enter a failsafe mode that caps engine speed on supercharged trucks.
- What to do
- It is not dangerous to shut off and restart, but have the control software updated so it does not strand you in traffic.
Screen reboots and the backup camera goes dark (recall)
- What you'll notice
- The center screen restarts over and over, and the rear camera view does not appear when reversing.
- Why it happens
- A software fault makes the infotainment unit reboot, which takes the camera display with it.
- What to do
- Have the software updated and look behind the truck yourself until then.
Cracked exhaust manifold (3.3L)
- What you'll notice
- A ticking or puffing sound from the engine bay, louder when cold, sometimes with an exhaust smell or a check engine light.
- Why it happens
- The manifold, most often on the right side, can crack or lose its studs after years of heating and cooling. Nissan published a service bulletin for this ticking noise.
- What to do
- Have the manifold inspected. It is not an emergency, but fix it before exhaust fumes start reaching the cab or the leak grows.
Rear camera image can be switched off (recall)
- What you'll notice
- No backup camera picture when you shift into reverse.
- Why it happens
- The display settings could be changed so the rear view stays off, which breaks federal camera rules. Nissan recalled affected trucks for an update.
- What to do
- Check your VIN for this recall. Until then, check mirrors and look behind you when backing up.
Daytime running lights dim after auto stop-start (recall)
- What you'll notice
- The daytime running lights go dim for a while after the engine restarts from an automatic stop.
- Why it happens
- A software error affects the lights after an idle stop-start restart. Nissan recalled affected trucks for an update.
- What to do
- Check your VIN for this recall and have the update done at your next dealer visit.
Headlight aiming marks missing (recall)
- What you'll notice
- Nothing shows while driving; the right headlamp has no readable aiming mark for a shop to use.
- Why it happens
- The required aiming reference was missing or unreadable on the right headlamp, so the beam may be set wrong.
- What to do
- Have the lamp inspected or replaced. Misaimed lights can dazzle other drivers or light the road poorly.
Repair prices for your Nissan Frontier
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace distributor assembly
- Replace cracked exhaust manifold and gaskets
- Replace lower steering column shaft and joint
- Replace radiator and flush transmission fluid
- Replace timing chains, guides and tensioners
- Replace front crash zone sensor
- Replace engine control relay in the fuse/relay box (IPDM)
- Replace fuel level sending unit
- Replace fuel level sending unit with revised float arm
- Replace rear axle shaft seal
- Replace driver airbag cover
- Replace front lower control links
- Replace both front wheel hub assemblies
- Check and reinstall circuit breaker correctly
- Inspect and reposition starter wire harness
- Replace ignition switch
- Update backup camera software
- Replace parking pawl pin and reprogram transmission module
- Reprogram transmission and engine control modules
- Replace all four tires
- Replace front right lower link with ball joint
- Update center display software
- Update engine control module software
- Replace door strikers
- Replace shift interlock pin and lock plate
- Replace front seat belt assembly
- Replace tail lamp bulb socket or lamp assembly
- Replace in-tank fuel pump assembly
- Replace shift cable lock plate
- Replace fuel filler inlet shutter valve
- Reseal sensor and replace rear wheel bearings
- Reprogram engine control module
- Replace oil cooler bolts and gasket
- Replace rear seat belt anchor nut and bolt
- Inspect and torque rear seat belt bracket bolts
- Install tow hitch assembly
- Update infotainment software
- Replace or re-mark right headlamp assembly
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.