Home › Warning lights › Reset a light › Pontiac
Reset a reminder light

How to reset the oil change and tire pressure lights on a Pontiac

These two lights are reminders, not faults. Do the work first, then reset. Everything else on your dash is a warning, and clearing it does not fix anything.

Oil change or maintenance reminder

1Pontiacs with an oil life readout in the cluster display, such as G6, G8, Grand Prix and Torrent
  1. Change the oil and filter first; the reminder is only reset after the fresh oil is in the engine.
  2. Turn the ignition to ON or RUN with the engine off.
  3. Press the DIC or trip information button on the steering wheel or stalk until the oil life reading appears.
  4. With the oil life reading showing, press and hold the reset button for the display, marked SEL, RESET or a check mark, for a few seconds.
  5. Release it when the oil life returns to full and the Change Engine Oil message clears.
  6. Start the engine and confirm the message stays off.

Pontiac put the reset control in different places by model: a steering wheel button on some, the trip odometer stem on the dash on others.

2Any Pontiac with no oil life item in the menu, or when the menu reset will not hold
  1. Only run this after the oil and filter have been changed.
  2. Turn the ignition on with the engine off; do not start it.
  3. Press the accelerator pedal all the way to the floor and release it three times within five seconds.
  4. Turn the ignition off, start the engine, and check whether the Change Engine Oil message is gone.
  5. If it is still on, the reset did not take, so repeat the three pedal presses more quickly.

This GM pedal sequence is documented across GM manuals of the Pontiac era; the five-second window is the part people miss.

Sources: ManualOwl · ManualsLib

Tire pressure (TPMS) light

1Pontiacs from about 2007 through 2010 with keyless entry, such as G5, G6, G8 and Torrent
  1. Set all four tires, and the spare if it carries a sensor, to the pressure on the Tire and Loading Information label inside the driver's door opening.
  2. Set the parking brake and turn the ignition to ON or RUN with the engine off.
  3. Press and hold the LOCK and UNLOCK buttons on the key fob together for about five seconds, until the horn sounds twice.
  4. Starting at the left front tire, hold a TPMS activation tool against the sidewall near the rim at the valve stem and press its button; wait for the horn chirp.
  5. Continue in the order left front, right front, right rear, left rear, waiting for a chirp at each corner.
  6. Turn the ignition off after the last chirp; if a sensor takes longer than two minutes, learn mode cancels and the sequence must be repeated from the start.

A TPMS activation tool is needed to wake each sensor. On many models the turn signal lights at the corner the car is waiting on.

2Pontiac Vibe, which does not use the GM relearn procedure
  1. Set all four tires to the pressure on the label inside the driver's door opening before anything else.
  2. Drive the car a few miles and see whether the low pressure light goes out on its own once the pressures are correct.
  3. Do not try the GM key fob sequence on a Vibe; its monitoring system is different and will not respond to it.
  4. If the light stays on, have the sensor relearn done with a scan tool at a tire shop or dealer.

The Vibe is called out in trade references as the exception to the GM procedure, but a verified step sequence for it was not available, so this stays general.

Sources: Tire Review · Brake & Front End

Worth knowing on a Pontiac

Pontiac ended production after 2010, so every one of these cars is on an older GM system; there is no touchscreen path for either reset. Earlier Pontiacs, roughly before 2007, may use a different tire monitoring setup than the fob sequence above, so check the owner's manual for the specific year.

If the light comes straight back

Pontiac models on the site

Button sequences vary by model year and trim. Your owner's manual is the final word for your exact vehicle. If a reminder will not clear after the service, something else is setting it.