Dodge Dakotaproblems, repair costs and recalls
Problems reported across 1996–2011. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
30 documented issues across all years, most serious first.
Oil sludge and loss of oil pressure
- What you'll notice
- The oil pressure gauge drops low or flickers, especially at idle when hot, the oil light comes on, or the engine starts knocking. In bad cases the engine seizes.
- Why it happens
- Thick sludge builds up in the oil pan and blocks the screen on the oil pump pickup, so the pump can no longer draw enough oil. Long oil change intervals and heat make it worse.
- What to do
- If the oil light comes on, pull over and shut the engine off. Have a shop drop the oil pan and clean the pickup screen before the bearings are damaged. Afterwards, change the oil and filter often.
Timing chain rattle and tensioner failure
- What you'll notice
- A rattle from the front of the engine for a few seconds at start-up, a check engine light with cam/crank timing codes (P0011 to P0017), misfires or a drop in power.
- Why it happens
- The timing chain tensioner and plastic guides on the 4.7L wear out early, especially when oil changes are skipped or the wrong oil is used. If the chain jumps a tooth the engine can be badly damaged.
- What to do
- Do not ignore a start-up rattle. Have the timing codes read and the chain inspected. Replacing the chain, guides and tensioner together is the usual fix.
Dropped valve seat causing misfire and lost power
- What you'll notice
- A steady misfire on one cylinder, a flashing or steady check engine light, rough running and lower power. Sometimes the engine suddenly starts ticking or knocking.
- Why it happens
- On these engines a valve seat pressed into the cylinder head can loosen and drop out, usually after the engine has run hot. The valve then cannot seal, and loose pieces can damage the piston.
- What to do
- If a misfire stays on one cylinder after new plugs and coils, ask for a compression or leak-down test. Stop driving if there is a new knocking sound. Fixing it means a rebuilt or new cylinder head.
Overheating and head gasket failure
- What you'll notice
- The temperature gauge climbs, coolant keeps going down with no visible leak, white sweet-smelling exhaust smoke, or milky oil.
- Why it happens
- The 4.7L is sensitive to heat. A tired water pump, thermostat, fan clutch or radiator lets it run hot, and overheating then damages the head gaskets and valve seats.
- What to do
- Stop driving as soon as the gauge rises. Have the cooling system pressure tested and a combustion-gas test done. Fixing the cooling part early is far cheaper than a head gasket job.
Automatic transmission slipping or failing
- What you'll notice
- Slipping when accelerating hard or going uphill, late or harsh shifts, the transmission stuck in one gear (limp mode), no reverse, or the truck not moving in gear.
- Why it happens
- The automatics in the Dakota wear out from heat, especially when towing or hauling, and the torque converter can fail. Old fluid speeds up the wear.
- What to do
- Check the fluid level and smell right away. If it slips or goes into limp mode, have codes read and get a transmission diagnosis before driving much more.
Upper ball joint wear and separation (recall)
- What you'll notice
- A clunk from the front end over bumps or when turning, loose steering, and in the worst case a front wheel that collapses inward.
- Why it happens
- Water gets into the front upper ball joints of 4x4 trucks, rusts them and wears them out early. A badly worn joint can pull apart. Recall 04V-596 covers 2000–2003 4x4 Dakotas.
- What to do
- Check your VIN for open recalls. If the front end clunks or the steering feels loose, have the ball joints inspected right away.
Free under recall 04V-596 for 2000–2003 4x4 trucks. Check your VIN.
Front ball joints wear out early
- What you'll notice
- Clunking from the front end, loose or wandering steering, uneven tire wear, or a wobble at speed.
- Why it happens
- The factory upper and lower ball joints are sealed and wear out quickly once their boots tear and water gets in, often well before 100,000 miles. A separated joint can let a wheel fold under.
- What to do
- Have the front end checked if you hear clunks. Replace worn joints in pairs and get an alignment afterwards.
Lower ball joints, tie rods and sway bar links wear
- What you'll notice
- Clunking or knocking over bumps, steering that feels loose, a pull to one side, or uneven tire wear. Some owners had a lower ball joint break.
- Why it happens
- The front lower ball joints, outer tie rod ends and sway bar end links on this generation wear out, and owners report replacing them from about 35,000 miles on.
- What to do
- Have the front end inspected at the first clunk. A broken ball joint can make you lose control, so do not put it off.
Front brake locks up and wheel overheats
- What you'll notice
- The truck pulls to one side, a front wheel gets very hot or smokes, there is a burning smell, and the pads or rotor on that side burn up.
- Why it happens
- A front caliper sticks and stays clamped, or a collapsed brake hose holds pressure on it. The brake then drags until it cools down.
- What to do
- If a wheel smokes or the truck pulls hard, stop and let it cool. Have the calipers and hoses checked; replace the caliper, hose, pads and rotor on that side.
Takata airbag inflators can rupture (recall)
- What you'll notice
- No warning signs. The danger is that in a crash the driver or passenger front airbag inflator can burst and throw metal pieces into the cab.
- Why it happens
- Airbag inflators made by Takata use a propellant that breaks down after years of heat and humidity. Recalls 15V-313 (driver) and 16V-352, 18V-021 and 19V-018 (passenger) cover these Dakotas.
- What to do
- Ask the dealer to check your VIN today and get the free replacement as soon as possible.
Free under the recall. Ask a dealer to check your VIN for open recalls.
Rear axle pinion nut can loosen and lock the axle (recall)
- What you'll notice
- Clunking or noise from the rear axle. In the worst case the rear wheels lock up while driving.
- Why it happens
- The nut that holds the drive pinion in the rear differential can work loose because not enough thread adhesive was used. Recalls 12V-474 and 13V-038 add a retainer.
- What to do
- Check your VIN for open recalls and have the free fix done. Get any new rear-axle noise checked promptly.
Free under the recall. Ask a dealer to check your VIN for open recalls.
Clockspring can disable driver airbag (recall)
- What you'll notice
- The airbag warning light comes on, and the horn or steering wheel controls may stop working.
- Why it happens
- Material inside the steering column clockspring can cut the ribbon wire that carries the airbag signal, so the driver airbag would not deploy. Recall 01V-153.
- What to do
- If the airbag light is on, have the codes read and check your VIN for the recall.
Free under recall 01V-153. Outside the recall, a clockspring is a paid part plus labor; ask for a written quote.
Brake tube or hose can be rubbed through (recall)
- What you'll notice
- A soft or low brake pedal, the brake warning light, or brake fluid leaking near a front wheel or the rear axle.
- Why it happens
- The left front brake tube can be worn through by a steering hose, and the rear brake hose can be punctured by the rear axle vent hose. Recalls 00V-193 and 00V-198.
- What to do
- If the pedal goes soft or fluid is leaking, do not drive the truck. Check the VIN for these recalls.
Free under the recall. Ask a dealer to check your VIN for open recalls.
Transmission fluid can leak onto exhaust (recall)
- What you'll notice
- Transmission fluid drips under the truck, or a burning smell or smoke from underneath.
- Why it happens
- Fluid leaking from the automatic transmission can land on the hot exhaust and catch fire. Recall 00V-197.
- What to do
- If you see smoke or smell burning fluid, stop and shut the engine off. Check the VIN for the recall.
Free under the recall. Ask a dealer to check your VIN for open recalls.
Truck may roll away in Park (recall)
- What you'll notice
- The shifter goes into Park but the truck can still roll, or it will not hold in Park.
- Why it happens
- A cup plug that holds the parking pawl shaft in the 42RLE automatic may be installed wrong, so the pawl does not hold. Recall 05V-460 adds a bracket.
- What to do
- Always set the parking brake until the recall is checked. Check your VIN.
Free under the recall. Ask a dealer to check your VIN for open recalls.
Computer faults can lock wheels or affect ABS (recall)
- What you'll notice
- Sudden wheel lock-up or loss of control, or ABS warnings.
- Why it happens
- A 2006 recall (06V-038) fixed an ABS control unit fault, and a 2007 recall (06V-341) reprogrammed the engine computer because the drive wheels could briefly lock.
- What to do
- Check your VIN to confirm the software updates were done.
Free under the recall. Ask a dealer to check your VIN for open recalls.
Intake plenum gasket leak burns oil
- What you'll notice
- The engine uses oil with no outside leak, pings under acceleration, idles rough or misfires, and oil can be seen inside the throttle body. Spark plugs and oxygen sensors foul.
- Why it happens
- The gasket under the stamped-steel plate on the bottom of the Magnum intake manifold fails, so oil vapor from the crankcase is pulled into the engine and burned. Chrysler issued a service bulletin (09-05-00) for it.
- What to do
- Have a shop check for oil in the intake and test for the leak. Fix it with an upgraded plate-and-gasket kit rather than just a new paper gasket, so it does not come back.
Camshaft position sensor failure
- What you'll notice
- Check engine light with codes like P0340 or P1391, hard starting or no start, rough idle, misfires or stalling.
- Why it happens
- The camshaft position sensor in the distributor gets dirty or fails with age, and the engine computer loses track of timing.
- What to do
- Have the codes read. The sensor is inexpensive and quick to replace; do not keep driving if the engine stalls in traffic.
Stalling while driving from crank sensor fault
- What you'll notice
- The engine cuts out while driving or coasting to a stop, idles rough, or cranks but will not start until it sits for a while.
- Why it happens
- On these trucks the crankshaft position sensor or its wiring connection fails, so the engine computer loses the signal it needs to run the engine. Owners also report a loose engine computer connector causing the same thing.
- What to do
- Have codes read right after a stall. A shop can check the crank sensor signal and its connector; replacing the sensor is a common first fix.
Radiator leaks and overheating
- What you'll notice
- Coolant on the ground at the front of the truck, low coolant, the temperature gauge rising, or steam from the radiator.
- Why it happens
- The radiators on these trucks crack and leak with age. The transmission cooler lines at the radiator can also start to leak.
- What to do
- Keep an eye on the temperature gauge and do not drive if it runs hot. Have the radiator and cooler lines pressure tested and replace the radiator if it is leaking.
Front wheel bearing or hub failure
- What you'll notice
- A humming or growling noise that grows with speed, a looseness in the front wheel, or an ABS light.
- Why it happens
- The front wheel bearings and hub units on these trucks wear out, sometimes quite early.
- What to do
- Have the wheel checked for play. A failing bearing can overheat and seize, so replace it soon.
Steering wheel shake when braking from warped rotors
- What you'll notice
- The steering wheel or truck shakes when braking from highway speed, sometimes with a pulsing pedal or a dragging, hot front wheel.
- Why it happens
- The front rotors warp from heat, often because a front caliper does not fully release.
- What to do
- Have the brakes inspected. Replace rotors and pads, and the caliper if it is sticking.
Rust on radiator support and body panels
- What you'll notice
- Bubbling paint on the rear fenders or doors, rust around the wheel wells, and rot on the radiator support under the hood, sometimes hidden by trim.
- Why it happens
- Road salt and trapped moisture rust the radiator support area and lower body panels on these trucks.
- What to do
- Inspect under the hood and around the fenders each year, especially in snowy states. Treat rust early; a rotted radiator support should be repaired by a body shop.
Wiper, lighting and wiring faults (recalls)
- What you'll notice
- The windshield wipers quit, the exterior lights stop working, or the horn and turn signals act up.
- Why it happens
- Three 2003 recalls: a wiper motor that can fail (04V-216), a central timer module that can shut off the lights (02V-322), and a dash wiring harness that can chafe (03V-389).
- What to do
- Check the VIN for open recalls and have them done for free.
Free under the recall. Ask a dealer to check your VIN for open recalls.
Manual-transmission truck may not start or may lurch (recall)
- What you'll notice
- The engine will not crank with the clutch pressed, or the truck moves when started.
- Why it happens
- Return springs in the clutch ignition interlock switch can break on manual-transmission trucks built July 2005 to July 2006. Recall 14V-795.
- What to do
- Check the VIN and have the switch replaced for free. Until then, start the truck with the clutch fully pressed and the parking brake set.
Free under the recall. Ask a dealer to check your VIN for open recalls.
Broken exhaust manifold bolts cause ticking
- What you'll notice
- A ticking or puffing noise from the engine bay that is loudest on a cold start and may fade as the engine warms up. Sometimes an exhaust smell.
- Why it happens
- The bolts holding the exhaust manifolds to the cylinder heads rust and snap from repeated heating and cooling, letting exhaust leak at the joint.
- What to do
- Not urgent, but have it fixed before more bolts break or the gasket burns through. Keep exhaust fumes out of the cab.
Transfer case output seal leak (4x4)
- What you'll notice
- Red fluid dripping from the middle of the truck, a burning smell, grinding when shifting into 4WD, or a whine at highway speed.
- Why it happens
- The rubber seals where the driveshafts leave the transfer case dry out and crack with heat and age.
- What to do
- Check the transfer case fluid level and have the leaking seal replaced before the case runs low and gets damaged.
Clicking behind dash and wrong air temperature
- What you'll notice
- A repeated clicking or ticking from behind the dashboard, or air that stays hot or cold no matter where the knob is set.
- Why it happens
- A plastic blend door actuator motor inside the heater box strips its gears or fails.
- What to do
- Not a safety problem. Have the actuator replaced; on many trucks it can be reached from under the dash.
Power window regulator breaks
- What you'll notice
- The window drops into the door, moves slowly or crooked, or the motor runs but the glass does not move.
- Why it happens
- The window regulator uses plastic parts that become brittle, especially in hot weather, and break.
- What to do
- Tape or prop the glass up to keep weather out and have the regulator replaced. Metal aftermarket regulators are an option.
Paint peeling off
- What you'll notice
- The paint or clear coat flakes and peels, usually on the hood, roof and other surfaces that get the most sun.
- Why it happens
- The factory paint finish loses adhesion and lets go of the primer after years of sun exposure.
- What to do
- Cosmetic only. Wash and wax to slow it, and get quotes for repainting the affected panels if it bothers you.
Repair prices for your Dodge Dakota
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Remove oil pan, clean or replace pickup screen, flush and refill oil
- Replace or rebuild one cylinder head with new gaskets
- Replace head gaskets (one or both sides)
- Replace intake plenum pan gasket with upgraded plate kit
- Replace camshaft position sensor
- Extract broken manifold bolts and replace bolts and gasket
- Replace crankshaft position sensor
- Replace radiator and refill coolant
- Replace automatic transmission with remanufactured unit
- Replace front lower ball joints and align
- Replace front wheel bearing/hub assembly (one side)
- Replace front caliper, brake hose, pads and rotors
- Replace front brake pads and rotors
- Replace HVAC blend door actuator
- Replace power window regulator (one door)
- Repaint affected panels
- Repair or replace rusted radiator support section
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Recall repair at a Dodge/Ram dealerNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.