Your 2003 Dodge Dakotaproblems, repair costs and recalls
What we've documented about the 2003 Dodge Dakota: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2003 Dodge Dakota
15 documented issues apply to 2003, most serious first.
Oil sludge and loss of oil pressure
- What you'll notice
- The oil pressure gauge drops low or flickers, especially at idle when hot, the oil light comes on, or the engine starts knocking. In bad cases the engine seizes.
- Why it happens
- Thick sludge builds up in the oil pan and blocks the screen on the oil pump pickup, so the pump can no longer draw enough oil. Long oil change intervals and heat make it worse.
- What to do
- If the oil light comes on, pull over and shut the engine off. Have a shop drop the oil pan and clean the pickup screen before the bearings are damaged. Afterwards, change the oil and filter often.
Timing chain rattle and tensioner failure
- What you'll notice
- A rattle from the front of the engine for a few seconds at start-up, a check engine light with cam/crank timing codes (P0011 to P0017), misfires or a drop in power.
- Why it happens
- The timing chain tensioner and plastic guides on the 4.7L wear out early, especially when oil changes are skipped or the wrong oil is used. If the chain jumps a tooth the engine can be badly damaged.
- What to do
- Do not ignore a start-up rattle. Have the timing codes read and the chain inspected. Replacing the chain, guides and tensioner together is the usual fix.
Dropped valve seat causing misfire and lost power
- What you'll notice
- A steady misfire on one cylinder, a flashing or steady check engine light, rough running and lower power. Sometimes the engine suddenly starts ticking or knocking.
- Why it happens
- On these engines a valve seat pressed into the cylinder head can loosen and drop out, usually after the engine has run hot. The valve then cannot seal, and loose pieces can damage the piston.
- What to do
- If a misfire stays on one cylinder after new plugs and coils, ask for a compression or leak-down test. Stop driving if there is a new knocking sound. Fixing it means a rebuilt or new cylinder head.
Overheating and head gasket failure
- What you'll notice
- The temperature gauge climbs, coolant keeps going down with no visible leak, white sweet-smelling exhaust smoke, or milky oil.
- Why it happens
- The 4.7L is sensitive to heat. A tired water pump, thermostat, fan clutch or radiator lets it run hot, and overheating then damages the head gaskets and valve seats.
- What to do
- Stop driving as soon as the gauge rises. Have the cooling system pressure tested and a combustion-gas test done. Fixing the cooling part early is far cheaper than a head gasket job.
Automatic transmission slipping or failing
- What you'll notice
- Slipping when accelerating hard or going uphill, late or harsh shifts, the transmission stuck in one gear (limp mode), no reverse, or the truck not moving in gear.
- Why it happens
- The automatics in the Dakota wear out from heat, especially when towing or hauling, and the torque converter can fail. Old fluid speeds up the wear.
- What to do
- Check the fluid level and smell right away. If it slips or goes into limp mode, have codes read and get a transmission diagnosis before driving much more.
Upper ball joint wear and separation (recall)
- What you'll notice
- A clunk from the front end over bumps or when turning, loose steering, and in the worst case a front wheel that collapses inward.
- Why it happens
- Water gets into the front upper ball joints of 4x4 trucks, rusts them and wears them out early. A badly worn joint can pull apart. Recall 04V-596 covers 2000–2003 4x4 Dakotas.
- What to do
- Check your VIN for open recalls. If the front end clunks or the steering feels loose, have the ball joints inspected right away.
Free under recall 04V-596 for 2000–2003 4x4 trucks. Check your VIN.
Front ball joints wear out early
- What you'll notice
- Clunking from the front end, loose or wandering steering, uneven tire wear, or a wobble at speed.
- Why it happens
- The factory upper and lower ball joints are sealed and wear out quickly once their boots tear and water gets in, often well before 100,000 miles. A separated joint can let a wheel fold under.
- What to do
- Have the front end checked if you hear clunks. Replace worn joints in pairs and get an alignment afterwards.
Front brake locks up and wheel overheats
- What you'll notice
- The truck pulls to one side, a front wheel gets very hot or smokes, there is a burning smell, and the pads or rotor on that side burn up.
- Why it happens
- A front caliper sticks and stays clamped, or a collapsed brake hose holds pressure on it. The brake then drags until it cools down.
- What to do
- If a wheel smokes or the truck pulls hard, stop and let it cool. Have the calipers and hoses checked; replace the caliper, hose, pads and rotor on that side.
Intake plenum gasket leak burns oil
- What you'll notice
- The engine uses oil with no outside leak, pings under acceleration, idles rough or misfires, and oil can be seen inside the throttle body. Spark plugs and oxygen sensors foul.
- Why it happens
- The gasket under the stamped-steel plate on the bottom of the Magnum intake manifold fails, so oil vapor from the crankcase is pulled into the engine and burned. Chrysler issued a service bulletin (09-05-00) for it.
- What to do
- Have a shop check for oil in the intake and test for the leak. Fix it with an upgraded plate-and-gasket kit rather than just a new paper gasket, so it does not come back.
Camshaft position sensor failure
- What you'll notice
- Check engine light with codes like P0340 or P1391, hard starting or no start, rough idle, misfires or stalling.
- Why it happens
- The camshaft position sensor in the distributor gets dirty or fails with age, and the engine computer loses track of timing.
- What to do
- Have the codes read. The sensor is inexpensive and quick to replace; do not keep driving if the engine stalls in traffic.
Stalling while driving from crank sensor fault
- What you'll notice
- The engine cuts out while driving or coasting to a stop, idles rough, or cranks but will not start until it sits for a while.
- Why it happens
- On these trucks the crankshaft position sensor or its wiring connection fails, so the engine computer loses the signal it needs to run the engine. Owners also report a loose engine computer connector causing the same thing.
- What to do
- Have codes read right after a stall. A shop can check the crank sensor signal and its connector; replacing the sensor is a common first fix.
Front wheel bearing or hub failure
- What you'll notice
- A humming or growling noise that grows with speed, a looseness in the front wheel, or an ABS light.
- Why it happens
- The front wheel bearings and hub units on these trucks wear out, sometimes quite early.
- What to do
- Have the wheel checked for play. A failing bearing can overheat and seize, so replace it soon.
Wiper, lighting and wiring faults (recalls)
- What you'll notice
- The windshield wipers quit, the exterior lights stop working, or the horn and turn signals act up.
- Why it happens
- Three 2003 recalls: a wiper motor that can fail (04V-216), a central timer module that can shut off the lights (02V-322), and a dash wiring harness that can chafe (03V-389).
- What to do
- Check the VIN for open recalls and have them done for free.
Free under the recall. Ask a dealer to check your VIN for open recalls.
Broken exhaust manifold bolts cause ticking
- What you'll notice
- A ticking or puffing noise from the engine bay that is loudest on a cold start and may fade as the engine warms up. Sometimes an exhaust smell.
- Why it happens
- The bolts holding the exhaust manifolds to the cylinder heads rust and snap from repeated heating and cooling, letting exhaust leak at the joint.
- What to do
- Not urgent, but have it fixed before more bolts break or the gasket burns through. Keep exhaust fumes out of the cab.
Transfer case output seal leak (4x4)
- What you'll notice
- Red fluid dripping from the middle of the truck, a burning smell, grinding when shifting into 4WD, or a whine at highway speed.
- Why it happens
- The rubber seals where the driveshafts leave the transfer case dry out and crack with heat and age.
- What to do
- Check the transfer case fluid level and have the leaking seal replaced before the case runs low and gets damaged.
Repair prices for your 2003 Dodge Dakota
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Remove oil pan, clean or replace pickup screen, flush and refill oil
- Replace or rebuild one cylinder head with new gaskets
- Replace head gaskets (one or both sides)
- Replace intake plenum pan gasket with upgraded plate kit
- Replace camshaft position sensor
- Extract broken manifold bolts and replace bolts and gasket
- Replace crankshaft position sensor
- Replace automatic transmission with remanufactured unit
- Replace front wheel bearing/hub assembly (one side)
- Replace front caliper, brake hose, pads and rotors
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Recall repair at a Dodge/Ram dealerNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…