Reset a reminder light

How to reset the oil change and tire pressure lights on a Audi

These two lights are reminders, not faults. Do the work first, then reset. Everything else on your dash is a warning, and clearing it does not fix anything.

Oil change or maintenance reminder

1Models from about 2010 onward with MMI and a rotary pushbutton or touchpad
  1. Reset this only after the oil and filter have actually been changed.
  2. Turn the ignition to ON with the car parked, then press the CAR function selector button.
  3. Press the Car systems or Systems control button.
  4. Select Servicing and checks, then Service intervals.
  5. Turn the rotary pushbutton to Reset oil change interval and press it to confirm.

Audi notes the remaining interval cannot be read back for the first few hundred miles after a reset, and that the countdown pauses while the battery is disconnected.

2Models with a SET button and a 0.0 button on the instrument cluster, roughly 2005 to 2015
  1. Change the oil first, then switch on the ignition without starting the engine.
  2. Press and hold the SET button on the cluster until the hour display starts to flash.
  3. Press SET repeatedly until the service interval display appears.
  4. Keep pressing until the oil change display is the one shown.
  5. Press and hold the 0.0 button for at least three seconds to reset it.

Cars of this era may show INSP for inspection and OIL for the oil change as two separate counters; only the oil counter resets this way.

3Models, mostly 2008 and newer, where neither the MMI nor the cluster offers a reset entry
  1. Confirm the oil has been changed before going any further.
  2. Turn the ignition on and look under CAR, then Systems, then Servicing and checks for a reset option.
  3. If there is no reset entry there and the cluster has no SET and 0.0 buttons, the interval cannot be reset from the driver's seat.
  4. Have a shop or Audi dealer reset the service interval through the diagnostic port with a scan tool.

This is common on Audis sold in the US, where the reset has to be done as a region-specific mileage reset rather than a simple one.

Sources: Manuales Audi · Ross-Tech Wiki

Tire pressure (TPMS) light

1Most models from about 2008 onward with MMI
  1. First set all four tires to the pressure on the label in the driver's door opening, with the tires cold and matched to the load you are carrying.
  2. Turn the ignition to ON with the car parked.
  3. Press the CAR function selector button.
  4. Select Tire pressure monitoring, or go to Car systems and then Servicing and checks.
  5. Select Store now and confirm, so the corrected pressures become the new reference.
  6. Drive normally afterwards so the system settles on the new values.

Audi's manual says the system must be reset through MMI every time pressures are adjusted, including a switch between partial-load and full-load pressures, and after any tire is changed or repaired.

2Models with a tire pressure button on the center console instead of an MMI entry
  1. Set all four tires to the door label pressure while they are cold.
  2. Turn the ignition to ON without starting the engine.
  3. Press and hold the tire pressure button until the display or the warning light confirms the new values are stored.
  4. Drive normally so the system can finish learning.

If your car has no such button, use the MMI path instead. The exact button marking varies by model year, so check the symbol matches the tire pressure warning light.

3Models with real pressure sensors in the wheels, after new sensors or a new set of wheels
  1. Set all four tires to the door label pressure first.
  2. Open the tire pressure page and check whether a separate pressure is shown for each individual tire.
  3. If individual pressures are shown, the car reads real sensors, and new sensors must be matched to the car electronically.
  4. Have a tire shop or Audi dealer code the sensors with a scan tool; no in-car sequence will do it.

Correcting pressures on these cars still only needs the store step. Only new sensors or new wheels need the shop.

Sources: ManualsLib

Worth knowing on a Audi

Most Audis sold here use an indirect tire pressure system that compares wheel speeds rather than reading sensors, so it has to be re-taught after any pressure change or rotation. Resetting a service reminder changes only the reminder, never the oil.

If the light comes straight back

Audi models on the site

Button sequences vary by model year and trim. Your owner's manual is the final word for your exact vehicle. If a reminder will not clear after the service, something else is setting it.