How to reset the oil change and tire pressure lights on a BMW
These two lights are reminders, not faults. Do the work first, then reset. Everything else on your dash is a warning, and clearing it does not fix anything.
Oil change or maintenance reminder
- Change the oil and filter first, then do this reset only after the work is finished.
- With the car parked, press the start button without your foot on the brake so the dash and screen come on.
- On the touchscreen, open the main menu and choose Vehicle, then Vehicle Status.
- Select the service requirements list to see the Condition Based Service items.
- Highlight the engine oil entry and choose the reset option, then confirm when the car asks.
- Check that the oil entry now shows a full interval before you switch the car off.
Menu wording varies between model years, and BMW only offers the reset when the item is at or near due. If the car refuses, the oil life still has distance on it.
- Finish the oil change first; only then reset the reminder.
- Press the start button once, or turn the key to the second position, without touching the brake and without starting the engine, so the whole dash lights up.
- Press and hold the trip odometer RESET button on the cluster for about ten seconds, until a service symbol and the first service item appear.
- Tap the same button to step through the items until the engine oil item is showing.
- Press and hold the button again for about five seconds, until the display asks you to confirm the reset.
- Let go, then press and hold the button once more for about five seconds to confirm.
- Switch the ignition off and back on, and check the oil item now shows a fresh interval.
The oil symbol shows red when a reset is still owed and amber once it has taken. If nothing changes, repeat the sequence; it sometimes needs a second try.
- Do the oil change first, then sit in the car with the doors closed.
- Press the start button once without touching the brake so the dash lights up.
- Press and hold the small BC or trip button on the end of the turn signal stalk until the service list appears in the cluster.
- Tap the same button to scroll to the engine oil entry, which shows the distance or time left.
- Press and hold the button again until a reset question appears, then hold once more to confirm.
- Turn the ignition off, then back on, and confirm the oil item reads a full interval.
This stalk sequence is from shop practice rather than a manual page we could open, and cars of this era differ. If the stalk does nothing, use the cluster RESET button method above.
Sources: YOUCANIC · AA1Car
Tire pressure (TPMS) light
- Set all four tires, and the spare if your car monitors it, to the cold pressure on the sticker in the driver's door opening.
- Switch the ignition on and open the menu, then choose Vehicle Info or Vehicle, then Vehicle Status.
- Select the tire pressure monitor entry and choose Perform Reset.
- Start the engine but stay parked, then select Perform Reset again to accept the pressures you just set.
- Drive away and keep above about nineteen miles an hour for a few minutes; the wheels show gray on screen while the reset finishes.
- Check the screen afterward: the warning should be gone and each corner should read a pressure.
Reset is also needed after a tire or wheel change or any time you deliberately run a different pressure, because the reset makes the current pressures the car's new reference.
- Set all four tires cold to the pressure on the door jamb sticker before touching the button.
- Start the engine and leave the car in park.
- Find the flat tire monitor button, usually on the center console near the shifter or low on the dash, marked with a tire and an exclamation point.
- Press and hold that button until the dash confirms the reset or the warning light blinks and goes out.
- Drive normally for several minutes so the system can relearn.
This era often uses the indirect monitor that watches wheel speeds, so it needs a longer drive. The button location is from shop practice; check your own manual for the exact spot.
Sources: ManualsLib · Capital One Auto Navigator
Worth knowing on a BMW
BMW tracks oil, brake fluid, brakes, inspection and other items separately, so resetting oil leaves the others alone. Tire pressure sensors have sealed batteries that die after several years, and on some models a replacement sensor has to be registered with a shop scan tool.