Home › Warning lights › Reset a light › Subaru
Reset a reminder light

How to reset the oil change and tire pressure lights on a Subaru

These two lights are reminders, not faults. Do the work first, then reset. Everything else on your dash is a warning, and clearing it does not fix anything.

Oil change or maintenance reminder

1Models from about 2020 on with the large center touchscreen (Outback, Legacy, Ascent and newer)
  1. Change the oil and filter first, then do this only after the fresh oil is in the engine.
  2. Turn the ignition to ON without starting off, so the center screen wakes up.
  3. Tap the gear or Settings icon on the center screen and look for the maintenance or service reminder list.
  4. Open the engine oil item in that list and choose the option that marks the service as done or resets the reminder.
  5. Confirm when the screen asks, then restart the car and check that the oil change message is gone.

We could not confirm the exact menu wording from a Subaru manual page; on some years the list sits under Vehicle Settings instead of Settings.

2Models roughly 2014 to 2019 that show an oil change message in the dash display
  1. Finish the oil and filter change first, then turn the ignition to ON with the engine off.
  2. Use the info or display button on the steering wheel to page the dash display over to the oil change message.
  3. Clear or acknowledge the message from that display, then start the engine.
  4. Watch the next few startups: on most of these cars the message is only a mileage reminder, so once dismissed it should stay away.

Exact button and menu steps vary by model and year and we could not verify one sequence from a Subaru source, so follow the display prompts rather than a fixed sequence.

3Models before about 2014, which mostly have no oil life monitor at all
  1. Change the oil and filter first, then write the mileage on the service sticker.
  2. Turn the ignition to ON and look at the dash: most Subarus of this era have nothing to reset.
  3. If an old green maintenance reminder light stays on, have a shop clear it, since it is cleared at a connector behind the dash and not with a button.

Sources: Rick's Free Auto Repair Advice · YourMechanic

Tire pressure (TPMS) light

1Most Subaru models from about 2008 on, which have no tire pressure reset button
  1. Set all four tires to the pressure on the driver's door jamb sticker first, with the tires cold.
  2. Check the spare too if your car shows a pressure for it, which only some newer models do.
  3. Start the engine and leave it running for about twenty seconds so the system reads the sensors.
  4. Drive at a steady speed above about twenty miles an hour for ten minutes or so.
  5. The low tire pressure light should go out on its own; if it stays on, one tire is still low or a sensor has failed.

Subaru does not give the driver a relearn button on these cars, so there is no button sequence to perform.

2After new tire pressure sensors, a second set of wheels, or a light that will not go out
  1. Confirm all four tires are at the door sticker pressure and the light still will not clear.
  2. Understand that new sensor ID numbers have to be written into the car, which no in-car button can do.
  3. Take the car to a tire shop or dealer and ask them to register the sensor IDs with a TPMS scan tool.
  4. Ask them to also check for a dead sensor battery, which is common on sensors more than about seven years old.

Sources: Capital One Auto Navigator · Rick's Free Auto Repair Advice · Brake & Front End

Worth knowing on a Subaru

Subaru does not use an oil life monitor on most of its cars, so the oil message is usually a simple mileage reminder. A flashing tire pressure light that then stays on means the system has a fault, not low air, and needs to be scanned.

If the light comes straight back

Subaru models on the site

Button sequences vary by model year and trim. Your owner's manual is the final word for your exact vehicle. If a reminder will not clear after the service, something else is setting it.