Reset a reminder light

How to reset the oil change and tire pressure lights on a Acura

These two lights are reminders, not faults. Do the work first, then reset. Everything else on your dash is a warning, and clearing it does not fix anything.

Oil change or maintenance reminder

1Models with the Multi-Information Display and an interface dial, roughly 2014 and newer
  1. Do this only after the engine oil has been changed, so the Maintenance Minder tracks the fresh oil.
  2. Park the car and turn the power mode to ON with the engine off.
  3. Press the SETTINGS button beside the interface dial.
  4. Turn the dial to Vehicle Settings and press ENTER.
  5. Move the dial left or right to the Maintenance Info tab, turn it to Maintenance Reset, and press ENTER.
  6. Move the dial down to RESET and press ENTER, then turn the dial to Reset and press ENTER to confirm.
  7. Check that the wrench icon and the maintenance code have cleared from the display.

Selecting Cancel instead of Reset backs out without changing anything. On the newest Acuras the same reset lives in the vehicle settings menu, though the on-screen wording differs by model year.

2Roughly 2004 through 2013 models with SEL/RESET and INFO buttons on the steering wheel
  1. Reset this only after the oil change is finished, not as a way to make the message go away.
  2. Turn the ignition to ON, position II; on keyless models press the start button to ON without pressing the brake.
  3. If the engine oil life is not already showing, press SEL/RESET on the steering wheel until it appears.
  4. Press and hold SEL/RESET for more than ten seconds, until reset mode for remaining oil life appears.
  5. Press INFO to highlight RESET, then press SEL/RESET to clear the maintenance codes and send oil life back to full.
  6. Pick CANCEL instead if you reached this screen by mistake and want to leave the reading alone.

Verified against the TL owner's manual; other Acuras of these years use the same two buttons, but the menu wording and the exact hold time can vary by model year.

Sources: Acura Canada · ManualOwl

Tire pressure (TPMS) light

1Models with indirect TPMS and a TPMS Calibration entry in vehicle settings, roughly 2015 and newer
  1. Set the cold pressure in all four tires to the driver's door jamb sticker figure first.
  2. Park on level ground, put the transmission in P, and set the power mode to ON.
  3. Open the settings menu on the screen and select Vehicle Settings.
  4. Select TPMS Calibration, choose Calibrate, and press the left selector wheel or the touchscreen to start it.
  5. If the screen says calibration failed to start, work through the same menu again.
  6. Drive about thirty minutes in total, mostly between 30 and 60 mph, to let calibration finish; a short flashing light while parked only means it is not done yet.

Calibration will not run with a compact spare fitted or tire chains on, and it has to be repeated after any pressure change, rotation or new tires.

2Roughly 2007 through 2014 models with a pressure sensor inside each wheel
  1. Set all four tires to the door jamb sticker pressure first and recheck them cold the next morning.
  2. Turn the ignition to ON; these cars give the driver no TPMS calibration menu and no reset button.
  3. Drive several miles at road speed so each sensor reports in, and the low pressure light should go out on its own.
  4. If the light stays on, or the TPMS warning flashes at startup, have a shop check it with a TPMS tool, because sensor IDs have to be registered with equipment.

Sensor batteries in these wheels last years, not forever, so a warning that keeps coming back at one corner usually points at a dead sensor rather than at low pressure.

Sources: Honda · Modern Tire Dealer

Worth knowing on a Acura

Acura uses the same Maintenance Minder codes as Honda, so reset only the item that was actually serviced. Which TPMS a given Acura has matters more than the model year alone: if the screen shows a pressure for each tire it is a sensor system, and if it only warns about low pressure it is the indirect system that needs calibration.

If the light comes straight back

Acura models on the site

Button sequences vary by model year and trim. Your owner's manual is the final word for your exact vehicle. If a reminder will not clear after the service, something else is setting it.