Reset a reminder light

How to reset the oil change and tire pressure lights on a GMC

These two lights are reminders, not faults. Do the work first, then reset. Everything else on your dash is a warning, and clearing it does not fix anything.

Oil change or maintenance reminder

1Most Sierra, Yukon, Acadia, Terrain and Canyon models roughly 2014 and newer with a center touchscreen
  1. Change the oil and filter first. Resetting the reminder only clears the message, so do it after the service, never in place of it.
  2. Park the vehicle, shift to Park, and turn the ignition to ON or RUN without starting the engine.
  3. On the center touchscreen, tap Settings, then Vehicle, and look for Oil Life or Oil Life Remaining.
  4. If the touchscreen has no oil life item, use the arrow buttons on the steering wheel to bring Oil Life up on the instrument cluster display instead.
  5. Select Reset, then confirm Yes.
  6. Check that the oil life reading has returned to full and that the CHANGE ENGINE OIL SOON message does not come back at the next start.

Menu wording varies by model year and radio. On several GMC trucks the oil life item appears only on the cluster display, not on the touchscreen.

2Models with DIC buttons on the steering wheel or dash, roughly 1999 through 2016
  1. Do this only after the oil and filter have been changed, since the reminder is the only thing you are clearing.
  2. Turn the ignition to ON or RUN with the engine off.
  3. Press the MENU or DIC buttons until the Oil Life Remaining reading shows on the display.
  4. Press and hold the SET/RESET button for more than five seconds. On a vehicle without DIC buttons, shift to Park and hold the trip odometer reset stem instead.
  5. Release the button once the oil life reading goes back to full life.
3Any GMC with the GM oil life system, as the fallback when the menu reset is missing
  1. Make sure the oil and filter are already changed before you touch the pedal, or the truck will under-report how worn the oil is.
  2. Turn the ignition to ON or RUN without starting the engine.
  3. Press the accelerator pedal slowly all the way to the floor and let it all the way back up, three times, within five seconds.
  4. Turn the ignition off, then start the engine and look at the oil life reading.
  5. If it reads full life and the CHANGE ENGINE OIL SOON message is gone, the reset took. If not, repeat the three pedal presses.

GM prints this pedal method for vehicles at every trim level, so it is the one to reach for when a menu reset cannot be found.

Sources: ManualsDir · ManualsLib

Tire pressure (TPMS) light

1Most models 2007 and newer, after a tire rotation or a sensor replacement
  1. First set all four tires, and the spare if it carries a sensor, to the cold pressure printed on the driver's door jamb sticker.
  2. Park, set the parking brake, and turn the ignition to ON or RUN with the engine off.
  3. Press MENU to reach Vehicle Information, scroll to the tire pressure screen, press SET/CLR to begin, then press SET/CLR again to confirm.
  4. Two horn sounds and a tire learning message mean the truck is listening for sensors, and the driver's front turn signal will light.
  5. Start at the driver's side front tire: let air out until the horn chirps once, then re-inflate it to the door sticker pressure.
  6. Repeat at the remaining three in this exact order: passenger front, passenger rear, driver rear. One chirp confirms each tire.
  7. Two horn sounds after the last tire means all four sensors are matched. Re-check and correct every pressure before driving.

You have about two minutes to teach the first tire and about five minutes for all four. If it times out after the first tire has learned, the stored sensor IDs are erased and the whole sequence must be run again.

2Models roughly 2007 through 2014 with a remote key fob and no tire pressure menu
  1. Set all four tires to the cold pressure on the driver's door jamb sticker before you start the relearn.
  2. Park, set the parking brake, and turn the ignition to ON or RUN with the engine off.
  3. Hold the lock and unlock buttons on the remote key fob together for about five seconds, until the horn sounds twice.
  4. Begin at the driver's side front tire: let air out until you hear one chirp, then bring the pressure back up.
  5. Work around the vehicle in this order, waiting for a chirp each time: passenger front, passenger rear, driver rear.
  6. Two horn sounds after the driver's rear tire means the relearn is complete. Set all four pressures again.

Learn mode cancels if the ignition is turned off, or if about two minutes pass with no sensor learned.

3Any GMC where the light came on from low pressure alone and no wheels were moved or replaced
  1. Set all four tires to the cold pressure on the driver's door jamb sticker first, checking them before the vehicle has been driven.
  2. Do not run a sensor relearn. The sensors are already matched to their wheel positions, so there is nothing to teach.
  3. Drive at more than about twenty miles an hour for several minutes so each sensor transmits its corrected pressure.
  4. The warning light should go out by itself during or shortly after that drive.
  5. If the light stays on, or the display shows dashes in place of pressure numbers, a sensor is not reporting and needs a relearn or replacement.

Sources: The Group Training Academy · Modern Tire Dealer

Worth knowing on a GMC

GMC shares its oil life and tire pressure systems with Chevrolet, so the same sequences apply across both brands. The oil life system reads engine operating conditions rather than counting miles, so the interval moves around. A pressure display showing dashes means a silent sensor, which no reset will fix.

If the light comes straight back

GMC models on the site

Button sequences vary by model year and trim. Your owner's manual is the final word for your exact vehicle. If a reminder will not clear after the service, something else is setting it.