Reset a reminder light

How to reset the oil change and tire pressure lights on a Dodge

These two lights are reminders, not faults. Do the work first, then reset. Everything else on your dash is a warning, and clearing it does not fix anything.

Oil change or maintenance reminder

1Most Dodge models from about 2013 on with the driver information display between the gauges
  1. Change the engine oil and filter first. The reset only clears the message, it is not a substitute for the service.
  2. With your foot off the brake, press the ENGINE START/STOP button, or turn the key one click, so the ignition is in ON/RUN and the engine is not running.
  3. Push and release the down arrow on the steering wheel to scroll to Vehicle Info.
  4. Push and release the right arrow to bring up the Oil Life screen.
  5. Press and hold the OK button until the oil life reads back at full.
  6. Push the up arrow to leave the submenu, then turn the ignition off and restart to confirm the message is gone.

If a pop-up says the engine must be off with the ignition in run, the engine was still running or the ignition was not in ON/RUN. Set it again and retry.

2Any Dodge where the cluster has no Oil Life screen, or the menu reset will not take
  1. Only do this once the oil and filter have been changed.
  2. Without pressing the brake pedal, place the ignition in ON/RUN without starting the engine.
  3. Press the accelerator pedal fully to the floor slowly, three times, within ten seconds.
  4. Return the ignition to the OFF position.
  5. Start the engine. If the oil change message comes back, the sequence did not register, so repeat it.

This is the factory secondary method and works across the Dodge, Jeep and Ram lineup. The three pedal presses have to be slow and complete.

Sources: ManualsLib · Mopar vehicle information · DodgeForum

Tire pressure (TPMS) light

1All Dodge models after correcting pressures or rotating tires. Dodge has no TPMS reset button
  1. First inflate all four tires to the cold pressure listed on the sticker in the driver's door opening.
  2. Read the sticker carefully on Charger and Challenger performance models, where the front and rear pressures are often different.
  3. Set pressures when the tires are cold, since a tire that has been driven on reads high and will end up underinflated.
  4. Drive the vehicle normally for up to twenty minutes, staying above about fifteen miles an hour.
  5. The tire pressure light turns off on its own once the system has received the corrected readings. No menu step is needed.

A low spare does not set the light on most Dodge models, and only a matching full-size spare carries a sensor at all.

2After a sensor, wheel or tire swap, or when the cluster shows SERVICE TPM SYSTEM
  1. Set every tire to the door-sticker pressure before trying to clear anything.
  2. Let the vehicle sit parked for at least twenty minutes, then drive it a minimum of twenty minutes at a continuous speed above fifteen miles an hour so the module learns the new sensor IDs.
  3. If the warning or the SERVICE TPM SYSTEM message survives that drive, the new IDs have to be programmed into the module with a TPMS tool and scan tool at a shop.
  4. Do not keep cycling the ignition hoping it clears. On these vehicles there is no key-and-button reset for TPMS.

A light that flashes for roughly a minute and a quarter at startup and then stays on solid is a system fault, not low pressure.

Sources: ManualOwl · Modern Tire Dealer

Worth knowing on a Dodge

Dodge shares its cluster and oil life software with Jeep, Chrysler and Ram, so the same two oil reset methods cover the whole line. Oil life is based on how the vehicle is driven rather than a fixed mileage counter. Neither of these lights needs a scan tool unless a TPMS sensor itself has been replaced.

If the light comes straight back

Dodge models on the site

Button sequences vary by model year and trim. Your owner's manual is the final word for your exact vehicle. If a reminder will not clear after the service, something else is setting it.