Home › Warning lights › Reset a light › Chevrolet
Reset a reminder light

How to reset the oil change and tire pressure lights on a Chevrolet

These two lights are reminders, not faults. Do the work first, then reset. Everything else on your dash is a warning, and clearing it does not fix anything.

Oil change or maintenance reminder

1Most models roughly 2014 and newer with a center touchscreen or a steering-wheel menu display
  1. Change the oil and filter first. This only clears the reminder, so reset it after the service is actually done, never instead of it.
  2. Park the vehicle, shift to Park, and turn the ignition to ON or RUN without starting the engine.
  3. On the center touchscreen, tap Settings, then Vehicle, then look for Oil Life or Oil Life Remaining.
  4. If there is no oil life item on the touchscreen, use the arrow buttons on the steering wheel to bring Oil Life up on the instrument cluster display instead.
  5. Select Reset and confirm Yes when it asks.
  6. Check that the oil life reading has gone back to full and that the CHANGE ENGINE OIL SOON message is gone at the next start.

Menu wording varies by model year and radio. On some trucks and SUVs the oil life item lives only on the cluster display, not the touchscreen.

2Models with DIC buttons on the steering wheel or dash, roughly 1999 through 2016
  1. Do this only after the oil and filter have been changed, because the reminder is the only thing being cleared.
  2. Turn the ignition to ON or RUN with the engine off.
  3. Press the MENU or DIC buttons until the Oil Life Remaining reading is showing on the display.
  4. Press and hold the SET/RESET button for more than five seconds. On a vehicle with no DIC buttons, shift to Park and hold the trip odometer reset stem instead.
  5. Let go when the oil life reading jumps back to full life.
3Any model with the GM oil life system, as a fallback when the menus will not cooperate
  1. Confirm the oil and filter have already been changed before you touch the pedal, or the vehicle will under-report how dirty the oil is.
  2. Turn the ignition to ON or RUN without starting the engine.
  3. Press the accelerator pedal slowly all the way to the floor and let it all the way back up, three times, within five seconds.
  4. Turn the ignition off, then start the engine and look at the oil life reading.
  5. If the reading is back to full life and the CHANGE ENGINE OIL SOON message is gone, it took. If not, repeat the three pedal presses.

This is the method GM prints for vehicles of every trim level, so it is the one to try when a menu reset is missing or greyed out.

Sources: ManualsDir · ManualsLib

Tire pressure (TPMS) light

1Most models 2007 and newer, after a tire rotation or a sensor replacement
  1. Before anything else, set all four tires, and the spare if it carries a sensor, to the cold pressure printed on the driver's door jamb sticker.
  2. Park, set the parking brake, and turn the ignition to ON or RUN with the engine off.
  3. Press MENU to reach Vehicle Information, scroll to the tire pressure screen, press SET/CLR to start, then press SET/CLR again to confirm.
  4. Two horn sounds and a tire learning message mean the vehicle is now listening for sensors.
  5. Starting at the driver's side front tire, let air out of that tire until the horn chirps once, then re-inflate it to the door sticker pressure.
  6. Do the same three more times in this exact order: passenger front, passenger rear, driver rear. One chirp confirms each one.
  7. Two horn sounds after the last tire means all four sensors are matched. Re-check every pressure before you drive.

You get about two minutes to teach the first tire and about five minutes for all four. If it times out after the first tire has learned, the old sensor IDs are erased and you must run the whole sequence again.

2Models roughly 2007 through 2014 with a remote key fob and no tire pressure menu
  1. Set all four tires to the cold pressure on the driver's door jamb sticker before starting the relearn.
  2. Park, set the parking brake, and turn the ignition to ON or RUN with the engine off.
  3. Hold the lock and unlock buttons on the remote key fob down together for about five seconds, until the horn sounds twice.
  4. Begin at the driver's side front tire: let air out until you hear a single chirp, then bring the pressure back up.
  5. Work around the vehicle in this order, waiting for a chirp at each one: passenger front, passenger rear, driver rear.
  6. Two horn sounds after the driver's rear tire means the relearn is finished. Set all four pressures again.

Learn mode cancels if the ignition is switched off or if about two minutes pass without a sensor being learned.

3Any model where the light came on from low pressure alone and no wheels were moved or replaced
  1. Set all four tires to the cold pressure on the driver's door jamb sticker first, checking them before the vehicle has been driven.
  2. Do not run a sensor relearn. The sensors are already matched to their positions, so nothing needs teaching.
  3. Drive the vehicle at more than about twenty miles an hour for several minutes so each sensor reports its new pressure.
  4. The warning light should go out on its own during or shortly after that drive.
  5. If the light stays on, or the display shows dashes instead of pressure numbers, a sensor is not reporting and a relearn or a new sensor is needed.

Sources: The Group Training Academy · Modern Tire Dealer

Worth knowing on a Chevrolet

Chevrolet's oil life system judges engine operating conditions, not just miles, so the interval it asks for will move around. A tire pressure display showing dashes rather than numbers means a sensor is silent, which no reset will cure. On many newer models a scan tool or TPMS activation tool does the relearn faster than deflating tires.

If the light comes straight back

Chevrolet models on the site

Button sequences vary by model year and trim. Your owner's manual is the final word for your exact vehicle. If a reminder will not clear after the service, something else is setting it.