Home › Warning lights › Reset a light › Chrysler
Reset a reminder light

How to reset the oil change and tire pressure lights on a Chrysler

These two lights are reminders, not faults. Do the work first, then reset. Everything else on your dash is a warning, and clearing it does not fix anything.

Oil change or maintenance reminder

1Pacifica, Voyager and 300, roughly 2017 and newer, with an OK button on the steering wheel
  1. Change the oil and filter first. This only clears the reminder, so do it after the service is actually done.
  2. Without pressing the brake pedal, push the ENGINE START/STOP button once so the ignition is in ON/RUN, and do not start the engine.
  3. Press the up or down arrow on the steering wheel until the cluster shows the Vehicle Info screen.
  4. Press the left or right arrow to open the Oil Life submenu.
  5. Hold the OK button until the oil life reads full again.
  6. Start the van or car and check that the oil change message is gone. If it comes back, run through the menu once more.

Pacifica Hybrid uses the same menu. Its oil life still counts down even though the gas engine runs less.

2Chryslers where the menu reset is not available, including key-start 300, 200 and Town and Country models
  1. Finish the oil and filter change before touching the reset, so the counter starts over on fresh oil.
  2. Without pressing the brake pedal, put the ignition in ON/RUN without starting the engine.
  3. Press the accelerator pedal fully to the floor slowly, release it, and repeat so you have pressed it three times within ten seconds.
  4. Put the ignition back in the OFF position, then start the car and confirm the oil change message has cleared.

This pedal method is the one Chrysler lists as the alternate reset. Exact steps vary by model year and cluster.

Sources: ManualsLib · Mopar vehicle information · ManualOwl

Tire pressure (TPMS) light

1All Chrysler models with the factory tire pressure monitor. There is no reset button for this light
  1. Set the pressures first. With the tires cold, fill all four to the cold pressure on the sticker in the driver's door opening, not the number molded into the tire.
  2. If your model has a monitored spare, set it to the same door-sticker pressure.
  3. Check the cluster display. It calls out the low tire and shows an Inflate To message with the pressure it wants.
  4. If the tires are warm from driving, you may need to add up to 4 psi over the door-sticker number for the system to accept them.
  5. Drive normally. It can take up to 20 minutes of driving above 15 mph for the sensors to report in, and then the light goes out by itself.
  6. Recheck the pressures cold later and let out any extra air you added while the tires were warm.

Chrysler has no in-cab TPMS reset step. Fix the pressures and the system clears the light on its own.

2Any Chrysler where the light stays on or blinks after all tires are set to the door-sticker pressure
  1. Verify every tire with your own gauge, since an inaccurate gas station gauge is the most common reason the light will not clear.
  2. A light that blinks for about a minute at each start and then stays on is a system fault, not a low tire.
  3. Usual causes are a sensor with a dead battery, a sensor damaged during a tire change, or new wheels whose sensors were never programmed.
  4. Have a shop read and relearn the sensor IDs with a TPMS tool, or replace the failed sensor. There is no driver sequence that does this.

Sources: Mopar vehicle information

Worth knowing on a Chrysler

Chrysler oil reminders run on mileage and driving conditions, so the reset is just you telling the car the work is done. Sensors in Chrysler TPMS have sealed batteries that typically last several years and are replaced as a unit.

If the light comes straight back

Chrysler models on the site

Button sequences vary by model year and trim. Your owner's manual is the final word for your exact vehicle. If a reminder will not clear after the service, something else is setting it.