How to reset the oil change and tire pressure lights on a Ford
These two lights are reminders, not faults. Do the work first, then reset. Everything else on your dash is a warning, and clearing it does not fix anything.
Oil change or maintenance reminder
- Change the oil and filter first. The reminder is a counter, not an oil sensor, so only reset it after the new oil is in.
- Turn the vehicle on, leave it in park, and wait for the center touchscreen to finish starting up.
- Touch Settings on the touchscreen, then touch Vehicle.
- Scroll to the oil life or oil change entry and touch it.
- Touch Reset and confirm, then check that the oil life reads full and the Oil Change Required message is gone.
On some of these models the oil life entry lives only in the instrument cluster menu. If Settings on the screen has no oil item, use the steering wheel method below.
- Have the oil and filter changed first, then do this reset once the service is actually finished.
- Turn the ignition to ON without starting the engine, or start it and leave the vehicle in park.
- Use the left-hand arrow pad to open Settings in the instrument cluster display.
- Arrow across to Vehicle, then down to Oil Life Reset.
- Press and hold OK (labeled Select on some years) until the display confirms the oil life is back to full.
Some years label the menu Vehicle Settings and the item simply Oil Life, but it is always inside the cluster Settings menu.
- Change the oil and filter first, and only then clear the reminder, because the message tracks mileage and driving conditions rather than oil condition.
- Turn the ignition to ON without starting the engine.
- Press the SETUP button (INFO on some models) over and over until the message center shows the oil life line, worded like OIL LIFE XXX HOLD RESET = NEW.
- Press and hold the RESET button until the message center shows the oil life back at full, usually with a confirmation that the oil life is set to new.
- Let go of RESET, turn the ignition off, then restart and confirm the Change Engine Oil Soon or Oil Change Required message no longer appears.
The SETUP and RESET buttons sit on the wiper stalk on some trucks and on the dash or center stack on others.
Sources: Ford · ManualsDir
Tire pressure (TPMS) light
- Set all four tires, plus the spare if it has a sensor, to the cold pressure printed on the sticker in the driver's door opening.
- Put the valve caps back on and make sure no tire was left over or under that number.
- Drive the vehicle above twenty miles an hour for at least two minutes.
- The light goes out on its own once the system sees good pressures. Most Fords have no reset button for this.
- If the light stays on after that drive, or blinks for about a minute every time you start the truck, a sensor or the system needs to be checked.
Cold weather alone can drop pressure enough to turn the light on, so always check the gauge before assuming a fault.
- First set all four tires to the front and rear pressures on the door sticker, since the two axles call for different numbers.
- Drive above twenty miles an hour for at least two minutes, then park somewhere safe where you can reach all four tires with an air pump.
- Turn the ignition off and leave the key in it, then turn the ignition on without starting the engine.
- Within ten seconds, switch the hazard flashers on and off three times. The horn sounds once and the tire pressure light flashes to show the system is in reset mode.
- Start at the left front: take the valve cap off and let air out until the horn chirps once, then do the right front, the right rear and the left rear in that order.
- Do each wheel within two minutes of the last one, then reinflate all four tires to the door-sticker pressures.
- A double horn chirp at any point means the reset did not take and the whole procedure has to be started over.
Stay at least three feet from another Ford running the same procedure. If the horn never sounds at the start, your model does not use this method.
- Set all four tires to the door-sticker pressure first, so you are not chasing a tire that is simply low.
- Plan on a shop visit for this one: Ford matches each sensor to its wheel position with a TPMS activation tool held against the tire, which the vehicle cannot do by itself.
- Ask the tire shop or dealer to relearn all four sensor positions after the new sensor is installed.
Exact steps vary by model year, and some newer models only accept the relearn through a scan tool.
Sources: ManualsLib · ManualsDir
Worth knowing on a Ford
Ford's reminder is a calculated oil life monitor, so it will not clear itself after an oil change. Ford has no TPMS reset button: on most models the light clears by driving once pressures are right, and only trucks and SUVs with different front and rear pressures need the hazard-flasher relearn after a rotation. Menu wording changes by model year.